SPECIFICATIONSBrand Name: MJJCCertification: ceCertification: EMCCertification: FCCCertification: LVDCertification: ROHSCertification: ULColor Temp(K): 6000KWaterproof: NoLEDs Number/M: 126LED Chip Brand: SANANLED Chip Model: SMD2835Origin: Mainland ChinaStrip type: SMDOccasion: LIVING ROOMAverage Life (hrs): 50000Power Source: DCSpecifications (light beads / m): 126Item Type: StripVoltage: 24VPower Generation: SWITCHIs Smart Device: YESChoice: yessemi_Choice: yesProduct Name: WS2811 Horse Race Led StripLED Type: SMD 2835 LED Qty: 126LEDs/MPCB width:10mm （ Some others use 8mm PCB, 10mm is better )Max Power: 8-10W/MWorking Voltage: DC 24VColor:Cool White/Natural White/ Warm WhiteColor Temperature: 3000K, 4000K, 6000KIP Rate: IP20 Non-waterproof Connector: 3 Pin Male & Female ConnectorPackage: 10M/RollConnection:Red Wire: +24VGreen Wire:DI/DATAWhite/Black wire: GND / -24V*** Wireless RF Controller with 3-Keys Panel Remote:Working Voltage: DC 24VMax Control Pixels: 3200 PixelsEffects Mode:Up to 23 Kinds effects. Speed and Brightness adjustableRemote: 3 Buttons, Speed/Brightness - ON/OFF - MODEBattery Powered by CR2032 Button Cell ( Battery not included)Our controller has short-circuit protection function*** How to setting pixels number?Step 1: Turn OFF the lightsStep 2: Long press 'Mode' keys 5 seconds,press 'Speed' keys to increase the pixels quantity, Press 'Mode' keys to decrease the pixels quantity.Step 3: Press ' ON/OFF' to save, Exit. Default factory setting is 80pixels,max up to 3200pixels. If you found some led strip is not light, please kindly do pixel setting as above steps.*** How to pair Remote to the Receiver,make them working 1 to 1 independently ?Step 1: Turn OFF the power supply.Step 2: Long press 'Mode'keys 3 seconds within 2seconds after powering ON.Step 3: Sucessfully if the led strip quick flash 3 times.1pc receiver can be controlled by max 6pcs panel remote.*** DC 24V Power Supply: Input Voltage: 110V / 220V ACOutput Votage: 24V DCOutput Power: 200W /100W /60WFeatures: No Noise, Real power output, long life-span.Advise: 1pc 24V 200W power supply to drive max 20m 24v 126leds/m running water light strips. if any big projects for longer strips, need add extra power supply each 10m.When you found the led strip light is flickering, please kindly add power supply, That is not Quality Problem !Ｍake sure do correct connection as the Wiring Diagram in the bottom of this page.
Description
SPECIFICATIONSBrand Name: MJJCCertification: ceCertification: EMCCertification: FCCCertification: LVDCertification: ROHSCertification: ULColor Temp(K): 6000KWaterproof: NoLEDs Number/M: 126LED Chip Brand: SANANLED Chip Model: SMD2835Origin: Mainland ChinaStrip type: SMDOccasion: LIVING ROOMAverage Life (hrs): 50000Power Source: DCSpecifications (light beads / m): 126Item Type: StripVoltage: 24VPower Generation: SWITCHIs Smart Device: YESChoice: yessemi_Choice: yesProduct Name: WS2811 Horse Race Led StripLED Type: SMD 2835 LED Qty: 126LEDs/MPCB width:10mm （ Some others use 8mm PCB, 10mm is better )Max Power: 8-10W/MWorking Voltage: DC 24VColor:Cool White/Natural White/ Warm WhiteColor Temperature: 3000K, 4000K, 6000KIP Rate: IP20 Non-waterproof Connector: 3 Pin Male & Female ConnectorPackage: 10M/RollConnection:Red Wire: +24VGreen Wire:DI/DATAWhite/Black wire: GND / -24V*** Wireless RF Controller with 3-Keys Panel Remote:Working Voltage: DC 24VMax Control Pixels: 3200 PixelsEffects Mode:Up to 23 Kinds effects. Speed and Brightness adjustableRemote: 3 Buttons, Speed/Brightness - ON/OFF - MODEBattery Powered by CR2032 Button Cell ( Battery not included)Our controller has short-circuit protection function*** How to setting pixels number?Step 1: Turn OFF the lightsStep 2: Long press 'Mode' keys 5 seconds,press 'Speed' keys to increase the pixels quantity, Press 'Mode' keys to decrease the pixels quantity.Step 3: Press ' ON/OFF' to save, Exit. Default factory setting is 80pixels,max up to 3200pixels. If you found some led strip is not light, please kindly do pixel setting as above steps.*** How to pair Remote to the Receiver,make them working 1 to 1 independently ?Step 1: Turn OFF the power supply.Step 2: Long press 'Mode'keys 3 seconds within 2seconds after powering ON.Step 3: Sucessfully if the led strip quick flash 3 times.1pc receiver can be controlled by max 6pcs panel remote.*** DC 24V Power Supply: Input Voltage: 110V / 220V ACOutput Votage: 24V DCOutput Power: 200W /100W /60WFeatures: No Noise, Real power output, long life-span.Advise: 1pc 24V 200W power supply to drive max 20m 24v 126leds/m running water light strips. if any big projects for longer strips, need add extra power supply each 10m.When you found the led strip light is flickering, please kindly add power supply, That is not Quality Problem !Ｍake sure do correct connection as the Wiring Diagram in the bottom of this page.